Casa de Lovely

Renovating In West Seattle

Posts Tagged pex

Catching Up With Casa de Lovely

Sep 15

Posted by Bryan in Electrical, Plumbing | No Comments

Since my last post I’ve gotten a bunch of smallish projects done, and I’ll address those before going into the stairs project and the painting project:

Plumbing

I spent a Saturday wrestling monkey wrenches over my head and broke back the galvanized water pipes to the most convenient joints, and substituted in PEX. I got everything installed, turned the water back on, checked all my joints, and found no leaks at all. Yay!

Then I noticed a drip. Grrr.

Turns out that I had a pinhole leak in a section of the galvanized that I hadn’t even touched. So I got to turn the water off again, heft the monkey wrenches again, and break out another section of galvanized. Luckily, that was the last of the work for the day. There’s still more galvanized, but it can wait until I can buy a manifold and replace it all.

I also ended up having to replace the kitchen sink supply valves (and then the flexible supply lines as well since they were clogged with galvanized pipe-rust), and the PEX-compatible ball valves were so easy to work with I don’t see any particular reason to mess around with copper stubouts and compression valves at all — just run the PEX out of the wall in a chrome sleeve and crimp a valve onto it and you’re all done.

Electrical

Of course, all the plumbing work was in support of putting in a new electrical panel. The guys from Kemly Electric came out and did a great job installing it and putting in the new mast, and then a couple days later the city moved the wires and put in the meter, and Kemly came back and set up the feeder line to the old panel.

I’ve moved the bathroom circuits and the cooktop circuit to the new panel. I suppose I could move the dryer circuit but I haven’t gotten around to it yet. The rest will have to wait until I start renovating rooms.

More Plumbing

Shortly after installing the supply lines, I went to run a load of laundry. I came back later to find the utility sink completely full of water. Apparently the drain had chosen that moment to clog. Since it’s the drain that serves the washing machine, the kitchen sink, and the dishwasher, I needed to fix it immediately.

So I basically rebuilt the entire trap, with long-throw bends and a cleanout, so it won’t clog as much and if it does I can unclog it without having to cut it all out again.

Before

After

Through all the frustration and work, I kept telling myself I was not going to call a plumber, dammit.

That completed, I decided the next day to finally install the new garbage disposal that’s been sitting in a box under the sink for almost a year. Installing it was pretty easy, except when I realized that it was physically larger than the old disposal and therefore the shunt over to the sink trap was at the wrong height.

So I basically had to completely rebuild that trap as well. Sigh. At least it’s now built so that it won’t accumulate ick in the shunt pipe, and I installed an air access valve so at least the kitchen sink now has a vent.

Kitchen disposal and trap rebuild

The neat thing about the garbage disposal is that it’s very very powerful. The damn thing sounds like a tractor engine starting up or something.

I think that’s it. Now on to the stairs…

Tags: , , , , ,

Electrical Upgrade Preparations

Jun 25

Posted by Bryan in Basement, Electrical, Plumbing, Why We Hate The Previous Owners | No Comments

We’re finally able to go ahead with upgrading the electrical service from 125 amp (and a totally-full, out-of-date, not-terribly-safe panel) to a nice shiny new 200 amp Siemens panel.

The plan is to install a new mast and meter in a better location on the house (where the wires won’t cross over the roof at no more than five feet clearance), run conduit back to the same room in the basement as the old panel, install the new panel there, put in a 100-amp breaker and run a feeder cable to the old panel. That way I can leave the horrible mess of electrical spaghetti untouched for now, and as I remodel rooms put new circuits in the new panel and retire circuits from the old panel until I can remove the old panel completely.

Also, the old panel is attached to a stud wall that I’m going to want to remove (well, it’s attached to the beam above a stud wall, but I wouldn’t want to remove the wall and leave the panel just hanging out in open space). The new location will let me reconfigure the walls however I like, and still leave plenty of room on that wall for washer/dryer/utility sink.

Before the electrician can come out, however, I’ve got a lot of work to do to prep the site. There’s a set of stairs from one of our back doors that needs to get detached and pulled away from the house so the conduit can run (I’ll cut a hole and put them back later). There’s a bunch of drywall that needs to get removed to clear a path for the grounding wire to reach the plumbing (at least the plumbing that will be left once I convert everything to PEX). And, most importantly, there’s a couple of water pipes directly over where the panel will go, which is forbidden by code (confirmed with an electrical inspector at the permit department).

So the plan is to cut out those pipes and divert them around the panel location using push-on or compression connectors and 3/4″ PEX. The problem is that they’re embedded in/hidden behind a plaster ceiling one of the previous owners installed in the whole central section of the basement (for fire protection from the furnace maybe? who knows).

Actually, I’m beginning to think that’s not plaster, it’s concrete. This hole took me half an hour beating on it with a crowbar and hammer:

Here’s a closeup, after some of the wire mesh lath has been cut away:

The reason I’m thinking it’s concrete is not only is it really hard but the sawzall will barely notch it (although it’s easy to cut out the mesh and keys once I’ve knocked off the visible layer).

So here’s the plan, before and after:

Hopefully I can at the very least get all the demo done on Saturday, and then I’ll be taking two days off work: the day the electrician comes to let him in and supervise and do any last-minute helpful homeowner things, and the day before to complete the plumbing and remaining demo.

Then the city’s inspection, then the Seattle City Light guy comes out for his inspection, then he schedules a crew for the re-splice to the service wire, and on that day the electrician comes back and makes the final hookup from the new box to the old, and then we have a completed upgrade.

Yay!

Tags: , , , , , ,

Things Start Going Back In

Sep 19

Posted by Bryan in Bathroom | 1 Comment

(or, Welcome to The Bathroom Renovation Death March, or, Plombieren Macht Frei.)

This is where things got bad. I was running out of time and the to-do list just kept getting bigger as I discovered step after intermediate step that I hadn’t planned for.

The plan was to finish up the framing, including framing in the hole where the old closet door was and building the stub wall to go at the foot of the tub, then to run the electrical back to the breaker panel, then tap into the existing feed lines and run PEX to the faucet, bath and toilet. Didn’t even come close.

First off, of course, is that I didn’t even get to the house until after 3pm, what with having to run around and pick up supplies, including my busted Craigslist Special circular saw from the repair shop way the hell up in Kirkland (about fifteen miles out of my way). Then I ate a sandwich and finally got to work about 4pm. I called the city and county and scheduled all the inspections for the following day. I was committed now.

Read the rest of this entry »

Tags: , , ,

Bathroom Demo Part 3

Sep 19

Posted by Bryan in Bathroom | No Comments

I haven’t been posting the last few days because I’ve either been too goddam busy or too goddam tired.

The difference between the DIY reality shows and reality is that the shows never show people covered in filth on top of a ladder working with heavy tools at arm’s length in the middle of the night.

Monday I pulled down the ceiling and dropped a huge pile of rockwool all over everything — I pulled one nail off the corner of each sheet of drywall and the whole thing came down. There were a bunch of nails in the joists, but the drywall must have been completely rotten. After I cleaned all of that up, I scraped up all the vinyl flooring and the linoleum underneath it (at least I hope it was linoleum). Also, the building inspector showed up for the preliminary inspection, and signed off on all our plans, including the stairs; what was especially useful is that he let me know that on old existing buildings they’re understanding about what’s possible and what isn’t, and with respect to the winding stairs that the 6″ inner width of the tread was the most important part and that if we missed the 10″ middle width by a quarter-inch or so they could let it slide.

Read the rest of this entry »

Tags: , , , , ,